motorola tips and tricks imei code

Show IMEI codeIf you need to know what's the IMEI code of your phone, simply press: * # 06 #you'll read it on display.Pin-Out1) Connected with 22pf to pin 32) RF out3) Connected with 33 pf to pin 8, 33 pf to pin, 33 pf to pin 74) BAT_FDBAK5) MAN_TEST connected with 10k to L2756) RS232_TX - connected to MCU SPI bus7) RS232_RX - connected to MCU SPI bus8) AUDIO_IN9) AUDIO_OUT10) Connected with 33 pf to pin 13, 33 pf to pin 1411) UPLINK -12) DOWNLINK -- DSC bus connected to the BIC13) DSC_EN_B -14) EXT_B+15) GndMotorola mtac EliteShow IMEI codeIf you need to know what's the IMEI code of your phone, simply press: * # 06 #you'll read it on display.Test ModeTo enter in Nam programming Mode, press: [arrow up]000000000000 (12 times zero)[MR]now display shows the first step of NAM programming; simply enter data and move to the next step using:* (the same key of [left arrow])Software versionTo see software version of your phone you need to short-circuit antenna ground with the two nearest pin together in the connector located under the phone. then: Power ON the phoneand type:#19#now display is showing software version of your phone.Serial NumberTo see the serial number of your phone you need to short-circuit antenna ground with the two nearest pin together in the connector located under the phone. then: Power ON the phoneand type:#75#now display is showing the first pair of digits, then go ahead using* (the same key of [left arrow])to show the second pair and so on.Pin OutThe pins are numbered 1 thru 10 from right to left ANT- (O) 1) Audio Ground2) Ext b+3) T Data4) C Data5) R Data6) Logic Ground7) Audio Out - on/off8) Audio In9) Manual Test10) Battery FeedbackMotorola Micro tacTest ModeTo enter in Nam programming Mode, you need to short-circuit the first and the third battery pin from the right, then: Power ON the phonedisplay will show "Tacs5", type in:55now display shows the first step of NAM programming; simply enter data and move to the next step using:* (the same key of [left arrow])Software versionTo enter in Nam programming Mode, you need to short-circuit the first and the third battery pin from the right, then: Power ON the phonedisplay will show "Tacs5", type in:19now display is showing software version of your phone.Motorola mtac EliteTest ModeTo enter in Nam programming Mode, press: [arrow up]000000000000 (12 times zero)[MR]now display shows the first step of NAM programming; simply enter data and move to the next step using:* (the same key of [left arrow])Software versionTo see software version of your phone you need to short-circuit antenna ground with the two nearest pin together in the connector located under the phone. then:Power ON the phoneand type:#19#now display is showing software version of your phone.Serial NumberTo see the serial number of your phone you need to short-circuit antenna ground with the two nearest pin together in the connector located under the phone. then: Power ON the phoneand type:#75#now display is showing the first pair of digits, then go ahead using* (the same key of [left arrow])to show the second pair and so on.Pin OutThe pins are numbered 1 thru 10 from right to left ANT- (O) 1) Audio Ground2) Ext b+3) T Data4) C Data5) R Data6) Logic Ground7) Audio Out - on/off8) Audio In9) Manual Test10) Battery FeedbackMotorola 8700Show IMEI codeIf you need to know what's the IMEI code of your phone, simply press: * # 06 #you'll read it on display.Turn on ClockTo turn on the hidden clock on your phone follow the following procedure:In Setup menu turn ON "extended menu"in language selection change to "GREEK" or "EAAKA"exit menupress key labeled "i" (the info key)type *#25625# and finallyturn OFF the phonenext time you'll wake up the phone the clock will be on your display and while surfing menu you'll find the option to set its time.RBS InfoTo activate RBS info menu simply press: [][][]113[]1[]OK ("[]" = the block you obtain pressing "*" for 3 seconds or more)this procedure seems not to work on all software version but it's the only one you can try from keypad.Software BugSome 8700 remain frozen after you switched on cell broadcast; the phone seems to function properly but it can't origin or receive any calls and turns off when you press any key